Step Instruction for Bathtub Installation
Step Instruction for Bathtub Installation
Blog Article
Each person has got his or her own opinion on the subject of Installing A Bathtub.
Installing a bathtub isn't specifically brain surgery, but it does need solid plumbing, woodworking, and in some cases, tiling abilities. Replacing an old tub with a brand-new one is likewise a reasonably difficult task. If the old bathtub is easily accessible, the job can relocate quickly; if you need to open a wall to eliminate the old bathtub and also position the new tub, the job is much harder. In either case, the job is within a house handyman's abilities, although you will certainly require an assistant to vacate the old tub as well as set in the new one. Make certain you have actually certified on your own for the work and also fit attempting it. Instead of hiring a professional to take over a halfway-completed job, it is much better to take into consideration utilizing one prior to you start. Possibilities are you may need an expert plumber to make tube connections.
This short article will help you install a new bath tub in your restroom if you have already acquired a brand-new tub and do not need to alter the plan of your previous supply of water pipelines.
Your devices and material list must make up the following:
Planning for the Installment
First of all, the sustaining frame supplied with the bathroom ought to be fitted (if needed) according to the supplier's instructions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is necessary to make sure that if the tap includes a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is likewise reasonable to fit a supporting plate under the faucets system to avoid strain on the tub.
Fit the flexible faucet ports to the bottom of both taps using 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bathroom. Utilize the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you make use of all of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to currently prepare to be suited its last setting.
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installation, after that the first thing you must do is detach the water system. After doing so, switch on the faucets to drain any water remaining in the system. The procedure of eliminating the existing taps can be fairly troublesome due to the limited gain access to that is usually the situation.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a cloth ready for the remaining water that will certainly come from the pipes. As soon as the supply pipes have been gotten rid of, use the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary faucets from turning during this procedure. As soon as the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any old sealing compound.
Before carrying on to fit the new taps, contrast the pipe connections on the old taps to the new taps. If the old taps are longer than the brand-new taps, then a shank adapter is required for the new faucets to fit.
Mounting the Bath tub
Making use of both wood boards under its feet, put the tub in the needed setting. The wooden boards are useful in evenly spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto 4 little points.
The following objective is to guarantee that the bathtub is leveled all round. This can be accomplished by checking the level as well as adjusting the feet on the bathtub till the spirit level reads degree.
To install taps, fit the bottom of the outermost adaptable faucet port to the suitable supply pipe by making a compression sign up with; after that do the same for the various other tap.
Activate the water and also examine all joints and also brand-new pipework for leakages and tighten them if necessary. Fill the tub and additionally examine the overflow electrical outlet and the normal outlet for leaks.
Lastly, take care of the bathroom paneling as described in the maker's user's manual. Tiling and sealing around the bathtub should wait up until the tub has actually been made use of at least once as this will certainly settle it right into its last setting.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damages to the thread. One end of the port fits on the plastic tail of the tap and the various other end gives a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly require reducing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the installing opening in the bath/basin ensuring that the washers are in place in between the tap and also the sink. Safeguard the faucet in position with the supplier offered backnut. Once the tap is securely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with normal tap connectors. The former kind should be connected to the tap ends first, tightening up just by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the location where the bathroom fulfills the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the fitting can relocate sufficient to split a stiff seal, triggering the water to penetrate the wall in between the bath and the tiling, leading to difficulties with dampness and possible leaks to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components and fittings. They are sold in tubes as well as cartridges, and can securing voids approximately a size of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to always load the tub with water before sealing, to enable the activity experienced when the tub is in use. The sealant can split fairly early if you do not think about this activity prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally quickly readily available on the marketplace. It is advisable to fit the tiles using waterproof or water resistant glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a devoted reader on A Step-by-Step Guide to Installing a Bathtub, I think sharing that section was really useful. Are you aware of another individual who is fascinated about the subject? Take a moment to share it. Many thanks for going through it.
Plumbing challenges? Professional solutions await. Report this page